Advertising
- Apc Back Ups Ns 1080 User Manual Instructions
- Back Ups Ns 1080
- Apc Back-ups Ns 1080 User Manual
- Apc Back Ups Ns 600
User Manual for APC Back-UPS, 900VA, 120V - BN900M-CA. Datasheet – APC Back-UPS, 900VA, 120V – BN900M-CA. Datasheet – APC Smart-UPS with Network Card – SMT1500NC →. BN1080G - Power Saving Back-UPS NS 1080VA. View the new All Products menu. Browse Products by Master Ranges. View the new All Products menu. User manual Back-UPS NS 1080 Installation and Operation. Size 185.2 KB. Date 10/7/13. User manual Back-UPS NS 1080 Installation and Operation. Back-UPS® Models 250, 400, 450, 600, 900 & 1250 User's Manual. Important safety instructions! This alternative power is derived from a battery within the UPS and provides the user with ample time to save files and properly close operations. American Power Conversion UPS). Installation and Operation Back-UPS 1250, 1300, 1500 5 Turn On the Back-UPS Press the Power ON button located on the top of the Back-UPS. The Power On LED will illuminate and a single short beep will be audible to indicate that the Back-UPS is providing protection for connected equipment. Aug 30, 2016 APC Back-UPS Device - 1080VA. New Battery Pack for APC Power Saving Back UPS NS 1080 BN1080G Compatible Replacement by UPSBatteryCenter 4.7 out of 5 stars 4. APC UPS, 1350VA Battery Backup & Surge Protector with AVR, Back-UPS Pro Uninterruptible Power Supply.
Back-UPS NS 600
User’s Guide
1
2
3
Connect Battery
Equipment
Power On and
Install Software
Install Software
990-2437A Copyright © 2007 American Power Conversion Corp.
All other trademarks are property of their respective owners.
Surge Protection
These outlets provide full-time protection from surges even if the
Back-UPS NS is switched OFF. Plug your printer, fax machine,
scanner, or other peripherals that do not need battery power into
these outlets.
Back-UPS NS is switched OFF. Plug your printer, fax machine,
scanner, or other peripherals that do not need battery power into
these outlets.
Battery Back-up plus Surge Protection
These outlets are powered whenever the Back-UPS NS is
switched ON. During a power outage or other utility problems
(brownouts, over-voltages), these outlets will be powered for a
limited time by the Back-UPS NS. Plug your computer,
monitor, CD-ROM drive and one other data-sensitive device
such as an external disk or tape drive, or Home Phoneline
Networking Association (HPNA) device into these outlets.
switched ON. During a power outage or other utility problems
(brownouts, over-voltages), these outlets will be powered for a
limited time by the Back-UPS NS. Plug your computer,
monitor, CD-ROM drive and one other data-sensitive device
such as an external disk or tape drive, or Home Phoneline
Networking Association (HPNA) device into these outlets.
Press the ON/OFF switch to power the unit
ON.
ON.
A single short beep and the green “Power”
indicator confirms the Back-UPS NS is on and
ready to provide protection.
indicator confirms the Back-UPS NS is on and
ready to provide protection.
The Back-UPS NS should charge for at least 16
hours to ensure sufficient runtime. The unit is
being charged whenever it is connected to utility
power, whether the unit is turned ON or OFF.
hours to ensure sufficient runtime. The unit is
being charged whenever it is connected to utility
power, whether the unit is turned ON or OFF.
If the red Building Wiring Fault indicator (located
on the end near the power cord) is lit, your
building wiring presents a shock hazard that
should be corrected by a qualified electrician.
on the end near the power cord) is lit, your
building wiring presents a shock hazard that
should be corrected by a qualified electrician.
Install the PowerChute
®
Personal
Edition
software
Place the PowerChute Personal Edition CD-
ROM into your computer and follow the
installation instructions on the screen.
ROM into your computer and follow the
installation instructions on the screen.
w
w
w.apc.com
®
APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.
Status
Visual Indicators
Audible Indicators
Alarm Terminates
When
On Line - UPS is supplying conditioned
utility power to the load.
utility power to the load.
Power LED - ON
None
n/a
On Battery - UPS is supplying battery
power to the load connected to the
Battery outlets.
power to the load connected to the
Battery outlets.
Power LED - ON
(off during beep)
(off during beep)
Beeping 4 times
every 30 seconds
every 30 seconds
UPS transfers back to
On Line operation, or
when UPS is turned
off.
On Line operation, or
when UPS is turned
off.
Low Battery Warning - UPS is supplying
battery power to the load connected to
the Battery outlets and the battery is near
exhaustion.
battery power to the load connected to
the Battery outlets and the battery is near
exhaustion.
Power LED - Flashing
Rapid beeping (half-
second intervals)
second intervals)
UPS transfers back to
On Line operation, or
when UPS is turned
off.
On Line operation, or
when UPS is turned
off.
Replace Battery - Battery needs to be
checked and/or replaced, or battery is not
connected.
checked and/or replaced, or battery is not
connected.
Power LED - Flashing
Constant tone
UPS turned off with
the power switch.
the power switch.
Overload Shutdown - During On Battery
operation a battery power supplied outlet
overload was detected.
operation a battery power supplied outlet
overload was detected.
Power LED - OFF
Constant tone
UPS turned off with
the power switch.
the power switch.
Sleep Mode - During On Battery
operation the battery power has been
completely exhausted and the UPS is
waiting for utility power to return to
normal.
operation the battery power has been
completely exhausted and the UPS is
waiting for utility power to return to
normal.
Power LED - OFF
Beeping once every
4 seconds
4 seconds
Utility power is
restored, or if utility
power is not restored
within 32 seconds, or
the UPS is turned off.
restored, or if utility
power is not restored
within 32 seconds, or
the UPS is turned off.
Building Wiring Fault - Your building
wiring presents a shock hazard that
should be corrected by a licensed
electrician.
wiring presents a shock hazard that
should be corrected by a licensed
electrician.
Building Wiring Fault
LED (red) - ON
LED (red) - ON
None
UPS is unplugged, or
plugged into a
properly wired outlet.
plugged into a
properly wired outlet.
Status Indicators
Power
Circuit
Breaker
AC Line
Cord
Building Wiring
Fault Indicator
UPS Power
Apc Back Ups Ns 1080 User Manual Instructions
Indicator
Power
Switch
®
See the Troubleshooting section for additional assistance.
For safety, the Back-UPS NS is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe
battery terminal. NOTE: Small sparks may occur during battery connection. This is normal.
battery terminal. NOTE: Small sparks may occur during battery connection. This is normal.
Turn the Back-UPS NS over and press in the
two release tabs. Slide the plastic battery
cover off the unit.
two release tabs. Slide the plastic battery
cover off the unit.
Insert the battery back into the compartment.
Slide the plastic battery cover in place until the
two tabs lock into place.
Slide the plastic battery cover in place until the
two tabs lock into place.
Connect the battery wire firmly to
the battery terminal.
the battery terminal.
1
2
3
Plastic Battery
Cover
Release Tabs
Battery Wire
Battery Terminal
Connect
Connect Modem / Phone / DSL / Fax / HPNA to Surge Protection
The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line -
DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, or
fax machines from surges when connected through the UPS as shown below.
DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, or
fax machines from surges when connected through the UPS as shown below.
Place the Back-UPS NS to avoid:
- Direct sunlight
- Excessive heat
- Excessive humidity or contact with fluids
- Excessive heat
- Excessive humidity or contact with fluids
Plug the Back-UPS NS power cord directly into a wall outlet; not a surge
protector or power strip.
protector or power strip.
Connect Computer Cable
The supplied cable and software provide automatic file saving and shutdown of the
operating system in the case of a sustained power outage.
operating system in the case of a sustained power outage.
Connect the cable to the Data Port of the Back-UPS NS. Connect the other end of the
cable to the USB port on your computer. The software will automatically find the USB
Port of your computer.
cable to the USB port on your computer. The software will automatically find the USB
Port of your computer.
DSL / MODEM /
Back Ups Ns 1080
WALL
TO COMPUTER USB PORT
FROM WALL JACK
Apc Back-ups Ns 1080 User Manual
DATALINE OUTPUT TO DSL,
MODEM, PHONE,
OUTLET
DATA PORT
FAX
Power
Battery Backup plus Surge Protection
Surge Protection
The Back-UPS NS indicates operating status
using a combination of visual and audible
indicators.
using a combination of visual and audible
indicators.
Advertising
Popular Brands
Apc Back Ups Ns 600
Popular manuals